Maple Leaf, King County
Dryer vent cleaning in Maple Leaf is priced at $105 to $295. The length of the duct and where it ends decide the figure. A vent that leaves through a ground-floor wall a few feet from the machine is at the bottom. One that runs across a basement ceiling, or rises through the house to a roof jack, is nearer the top, as is any vent blocked by a nest.
Typical investment
$105–$295
Book an inspection
Book your $99 inspection
$99 plus tax, deducted when you approve the repair
Not sure where to start
Pick what you're seeing at your Maple Leaf home — we'll point you to the right fix.
What we do
The same crew, the same written quote — for Maple Leaf homes.
A Level 1 review of everything reachable, raised to a Level 2 camera scan when a question stays open
Learn more
The whole flue brushed, using heads picked for the liner's size and shape
Learn more
A photo assessment that distinguishes surface wear from structural damage
Learn more
Camera survey and measurements taken before any liner is chosen
Learn more
Measurement of each flue, or of the crown when a single cap will span several
Learn more
Glass removed, cleaned and checked for a sound gasket
Learn moreRanges shown for orientation — the exact figure is written up on-site, after the inspection.
Maple Leaf has a record of looking after itself. Residents formed the Maple Leaf Community Council in 1983, and three years later the neighborhood was honored in the national Neighborhood of the Year competition. Household upkeep is a private version of that habit, and the dryer vent is the item most often left off the list, because it is behind an appliance, inside a wall and out of sight for its entire length.
Every dryer vent cleaning we do in Maple Leaf includes:
Smoke coming back into the room, or a smell that won't go? Book the inspection first.
Book nowLooking at 2008 through 2010, the U.S. Fire Administration put the national toll of dryer fires in homes at roughly 2,900 a year, with around five people killed and a hundred hurt each year, and January was the peak month. January is also when a Seattle household runs the dryer most, since nothing dries on a line outdoors. A vent narrowed by lint makes the machine run hotter and longer in exactly that month.
Before anything is touched, we measure the air arriving at the exterior hood.
The dryer is moved, the connector removed, and the exterior hood opened so the duct can be worked from either side.
Spinning brushes loosen the lint while suction pulls it out, section by section.
Everything is reconnected with metal clamps and tape rated for the purpose, and the new airflow figure is written beside the old.
What this work is quoted at for Maple Leaf homes — the exact figure comes from the $99 on-site inspection, credited toward the work.
| Service | Price in Maple Leaf | What that covers |
|---|---|---|
| Dryer Vent Cleaning | $105–$295 | Full run cleaned; roof or upper-floor terminations at the top |
| Chimney Sweep | $209–$459 | Full flue swept, Level 1 inspection included |
| Chimney Inspection | $99 plus tax | Level 1 visual; Level 2 adds a full camera scan |
| Chimney Relining | From $1,900 | Full-length stainless liner, sized to the appliance |
| Chimney Repair | From $425 | Masonry repair — brick and mortar, scoped after diagnosis |
Ranges are what these jobs are quoted at in Maple Leaf. The exact figure is set on site after a $99 inspection (credited toward the job if you go ahead), and you approve it before any work starts.
Maple Leaf is a hilltop neighborhood that reaches 466 feet at 92nd Street and Roosevelt Way, with houses from before 1940 through the 1950s, on both sides of the old city limit at 85th Street.
Maple LeafKing County, WA · 47.696, -122.317
Before and after
Illustrations of what each repair changes on a typical chimney — not photos of a specific job.
Before
After
Before
After
Before
After
Four steps, each one on paper — so you always know what happens next.
Choose a genuine opening on the crew's calendar. Confirmation is immediate.
Liner, crown, cap, flashing and masonry examined in order — each finding photographed.
One document, plain numbers, covering only the work your chimney genuinely needs.
The repair is completed, then handed over with before-and-after photos of every item.
It can be. Thin foil and plastic connectors crush easily and catch lint in their ridges. We point it out and can replace it with semi-rigid metal during the visit.
A short, straight run can be brushed with a kit from a hardware store. Long runs, roof exits and ducts with several bends are where a kit's rods come apart inside the pipe, and those are jobs for powered equipment.
Yes, where the vent serves a single unit and we can reach both ends. Shared building exhaust systems need the association's agreement first.
A $99 on-site inspection, a written quote before any work, and photos of every item we touch.
